PrintE-mail


Quadrotor kit with Hobbyking i86 Multi-Rotor Control Board
View Full-Size Image


Quadrotor kit with Hobbyking i86 Multi-Rotor Control Board

Product ID: NR-QD-KIT-HK-i86
Weight: 2 kg
Price: Rs.15,480.34

Ask a question about this product

  
In Stock: 1
Usually ships in:

2-3d.gif

Introduction

This is a combination of well known and time tested HobbyKing i86 multirotor controller board with matched Quad Frame, BLDC motors, ESCs and propellers to help you quickly build your own Quadrotor platform.

Controlled by an Atmel Mega168PA 8-Bit RISC based micro controller and utilizing a single 3-axis MEMS gyro the Hobbyking i86 Multi-Rotor Control Board is capable of 8 Multi-rotor craft types and 2 flight modes without the need to flash the micro controller. The simple dip switch systems allows for quick and easy selection of your desired Multi-rotor configuration and flight mode. The flight controller specifications are,

  • Input Voltage: 4v to 6v
  • Input signal: 50hz standard PPM
  • PWM Frequency: 400hz for ESC, 50hz for servos
  • Gyro scale: +/- 500dps, ODR: 800hz
  • Operating temp: -40° C to 85° C
  • Size: 40mm x 40mm
  • Weight: 8g

The Hobbyking i86 Multi-Rotor Control Board supports:

  • Aero (fixed wing)
  • Dual copter
  • Tri copter
  • Quad copter X
  • Quad copter +
  • Hex copter
  • H6 copter
  • Y6 copter

All of the above modes can be set in "Normal" mode or "Sports" mode (default normal)

For more information on flight controller, please refer to HobbyKing website here.

Important Note: The support for all queries related to flight controller is available directly on Hobby king website.

Quadrotor 49.5cm Diameter Frame is a sturdy yet light weight frame which is capable of surviving repeated crashes. It comes with dedicated power distribution board for connecting LiPo battery with all ESCs. Each N2822 1800kv BLDC motor with its 8x4.5 inch (20x 11cm) Pusher and Puller Propeller Matched Pair is capable of providing maximum thrust of 900gms per motor.

This quad rotor is capable of providing maximum thrust of 3.6Kgs. The approximate weight is around 1.2Kgs. The ESCs included in the package can drive motors with continuous 20Amp load current. This ESC is factory programmed and ready to use (Product code: NR-BLDC-MD20).

Note: Kit comes in unassembled form

Kit contains

Hobbyking i86 Multi-Rotor Control Board: Qty 1
N2822 1800Kv Brushless DC Outrunner Motor: Qty 4
Quadrotor 49.5cm Diameter Frame: Qty 1
20Amp BLDC ESC: Qty 4
8x4.5 inch (20x 11cm) Pusher and Puller Propeller Matched Pair: Qty: 2 Pair

Required

FS-CT6B 6ch 2.4GHz transmitter & receiver: Qty 1
Lithium Polymer 3 Cell, 11.1V, 5000mAh, 20C discharge Battery: Qty 1
Protection Circuit for 3 Cell Li-Po Battery: Qty 1
B6AC Universal Battery Charger: Qty 1

Warning: Flying multirotor platforms requires considerable amount of practice and skill. If not handled correctly, it can cause severe injury. Please read the flight controller manual carefully before starting. Please make sure that you remove the props before doing any caliberation and/or configuration changes.

Disclaimer: Nex Robotics will not be responsible for any injuries or damages caused while operating this platform.

Visit forum for Online Discussion on this product



ROHS Compliant : YES


Customer Reviews:

There are yet no reviews for this product.
Please log in to write a review.


You may also be interested in this/these product(s)

B6AC Universal Battery Charger
B6AC Universal Battery Charger
Rs.2,778.51

FS-CT6B 6ch 2.4GHz transmitter & receiver
FS-CT6B 6ch 2.4GHz transmitter & receiver
Rs.4,130.00



Customers who bought this product also bought this/these product(s)

B6AC Universal Battery Charger
B6AC Universal Battery Charger
Rs.2,778.51
Camera Pod
Camera Pod
Rs.2,021.51