Print Print
Print
10mm Metal Stud60 RPM Centre Shaft Economy Series DC Motor

Hercules Lite 6V-36V, 8Amp Motor Driver
View Full-Size Image


Hercules Lite 6V-36V, 8Amp Motor Driver

Product ID: NR-MDR-001
Weight: 120 gms
Price: Rs.1,438.80

Ask a question about this product

  
In Stock: 14

Introduction
Hercules Lite 6V-36V, 8Amp Motor Driver can take up to 30A peak current load and can be operated up to 10KHz PWM. Motor driver can be interfaced with 3.3V and 5V logic levels. Motor driver has built-in protection from under / over voltage, over temperature and short. Motor driver has terminal block as power connector and 7 pin relimate connector for the logic connection. It is suitable for high performance robots, Robocon, Robocup, US First, Battle robots etc.

Specifications

  • Operating voltage: 6V to 36V
  • Continuous output current: 8Amp
  • Peak output current: 30Amps
  • Maximum PWM Frequency: 10 KHz
  • Over voltage and under voltage shutdown
  • Thermal shutdown
  • Protection against loss of GND and Vcc.
  • Motor fault diagnostics outputs for over temperature or short circuit
  • Power Connector: 4 Pin Terminal Block
  • Logic Connector: 7-Pin relimate connector (2510 type)
  • Size: 51.3mm x 27.7mm

Package contains
Hercules Lite 6V-36V, 8Amp Motor Driver
15cm, 7-pin relimate connector with wire
Four 10mm mounting studs
Eight M3 mounting screw

Download Product Manual
Motion control example based on ATMEGA640 Development Board

Important

  • Motor driver is factory shipped with 1000uF capacitor mounted across Vcc and Ground on the board as shown in figure below. However for space constrained application you can remove this capacitor and connect it across the supply and as near as possible to the motor driver.
  • Use multithread copper wire with at least 1.5mm2 area of cross section for proper current handling capacity.
  • It is highly recommended to use of 15A or 20A fuse in between motor driver’s supply line.
  • Motor driver is not reverse polarity protected. Applying reverse polarity will instantly damage the motor driver.
  • Make sure that motor supply ground and logic ground is common.
  • If you change motor’s direction suddenly while motor is moving in one direction even at 4Amps, depending on the type of the motor, surge current may reach to very high value and motor driver may go in to protection mode. Do not reverse the motor’s direction suddenly unless its required. It’s a good practice to give stop command to the motor for 10 to 100 milliseconds between sudden direction changes.

with-cap

Correct Motor Driver Selection

For generic motion control applications we recommend Hercules series motor driver that provides satisfactory performance at affordable price. However, for precision servo control applications, Super Hercules series motor driver is strongly recommended. Following is the difference between these two series of the motor drivers.

In case of the Hercules series Motor Drivers, the PWM OFF signal switch off the lower MOSFETs. Which means during PWM off period the motor is free wheeling. DC braking is achieved by connecting IN-1and IN-2 to the logic 1 or logic 0 simultaneously.

Super Hercules series Motor Drivers actually shorts the motor winding during PWM off cycle for tight motion control. It also uses Synchronous Rectification to reduce power dissipation across MOSFETs when motor windings are shorted. In order to do all this, it uses high power MOSFETs and smart motion control methods. In this case, DC braking is achieved by simply setting PWM to logic low.

Interfacing motor driver with the microcontroller

Hercules-HV-Motor-Driver-Mi

To drive the motor controller you just need PWM, IN-1 and IN-2 pins. These pins can have 5V as well as 3.3V logic levels. Diagnostics 1 (DG1) and Diagnostics-2 (DG2) pins are internally pulled up at 5V at the motor driver side and are only required if you want to detect over temperature and short circuit faults. Most of the microcontrollers which operate at 3.3V have 5V tolerant input pins. If pins are not 5V tolerant then to interface them to 3.3V logic level you need to scale down 5V to 3.3V logic using open collector buffers or any other 5V to 3.3V logic converters.

Use Fuse Holder with Fuse Blow Indicator to protect motor driver from overload

soft-fuse-blow-indicator-fr

Recommended Motors
Super Hercules DC Motor with Planetary Gearbox and Side Shaft Super Heavy Duty DC Gear Motors
Super-Hercules-Planetary-Ge Side-Shaft-Super-Heavy-Duty
Recommended Battery Any High discharge 3cell 11.1V Lithium Polymer battery above 1800mAh.

 

Any High discharge 3cell 11.1V Lithium Polymer battery above 1800mAh. Any High discharge 3cell 11.1V Lithium Polymer battery above 1800mAh.

Connections

pin-config

Motor Connector Pins

Pin Functionality
Ground Ground pin to be connected to the supply
Vcc Motor supply 6V to 36V DC
OUT-1 (A) Output 1 for the motor
OUT-2 (B) Output 2 for the motor

Logic input Connections

Pin No. Pin Functionality
1 GND Ground
2 IN-1 Logic input for the motor direction.
3 Diagnostic 1
(DG-1)
Output pin with logic 1 output in normal operation. Represents side of the internal
H bridge corresponding to IN-1. Pin is pulled to logic low by the motor driver in
case of over temperature or overload due to short circuit.
4 PWM Used to apply Pulse Width Modulation to control motor velocity
5 Diagnostic 2
(DG-2)
Output pin with logic 1 output in normal operation. Represents side of the internal
H bridge corresponding to IN-2. Pin is pulled to logic low by the motor driver in
case of over temperature or overload due to short circuit.
6 IN-2 Logic input for the motor direction.
7 CS* No Connection

Note:
Ground of the Motor Connector and Logic input Connector are internally shorted.
If you want to drive motor without using PWM then connect PWM pin to 5V logic level.

Truth Table in Normal Operating Conditions

IN-1 IN-2 Diagnostic 1
(DG1)
Diagnostic 2
(DG2)
OUT-1
(A)
OUT-2
(B)
CS Mode of Operation
1 1 1 1 H H N.A. Break to VCC
1 0 1 1 H L Yes Clockwise(CW)
0 1 1 1 L H Yes Counterclockwise
(CCW)
0 0 1 1 L L N.A. Break to GND

In all above cases logic 0 and logic 1 on PWM pin will turn off or turn on internal low side MOSFETs.

Visit forum for Online Discussion on this product



ROHS Compliant : NO


Customer Reviews:

There are yet no reviews for this product.
Please log in to write a review.



Customers who bought this product also bought this/these product(s)

Terminal Block big 508/2
Terminal Block big 508/2
Rs.20.40
SPDT 12V Sugar Cube Relay
SPDT 12V Sugar Cube Relay
Rs.22.68
T Type Battery Connector
T Type Battery Connector
Rs.58.80
Female 1 to 1 Connector Pack of 10
Female 1 to 1 Connector Pack of 10
Rs.42.00