Print Print
Print
P89V51RD2 robotics boardP89V51RD2 Adaptor Board

B6AC Universal Battery Charger
View Full-Size Image


B6AC Universal Battery Charger

Product ID: NR-BLIC-B6AC
Weight: 800 gms
Price: Rs.2,778.51

Ask a question about this product

  
In Stock: 7

Introduction

B6AC Universal Battery Charger can charge 2 to 6 Cell Lithium Polymer battery packs, 1 to 15 NiMH / NiCd battery packs, and 2V to 12V Lead Acid Battery. The charging current is user programmable between 0.1 to 6Amps. It also features a balance charger for Lithium Polymer Battery chemistry where it balances battery with drain current of up to 300mA per cell. It has very simple interactive user interface based on 2x16 alphanumeric LCD along with 4 menu switches. It also includes charging cables for 5 different types of battery sockets. This charger works on mains supply as well as 11 to 18V DC.

Features

  • Lithium Polymer Battery
    • Charging modes: Normal, Balance, Fast, Storage
    • Number of cells: 2 to 6 Cell battery packs
    • Charging current: User programmable 0.1 to 6Amps
    • Balance charging: in built independent 300mA current drain per cell
    • Discharge capacity: 5W
  • NiMH/NiCd Battery
    • Charging modes: Normal, Automatic charge and discharge for ‘N’ cycles
    • Number of cells: 1 to 15 Cell battery packs
    • Charging current: User programmable 0.1 to 6Amps
    • Discharge capacity: 5W
  • Lead Acid Battery
    • Charging modes: Normal
    • Number of cells: 2 to 10 Cell battery packs
    • Charging current: User programmable 0.1 to 6Amps
    • Discharge capacity: 5W
  • User settable programs

Specifications

  • Supported Battery: Lithium Polymer, NiMH, NiCd, Lead Acid
  • Battery capacity: Refer to Features
  • Operating voltage: 100-240V AC, 11 to 18V DC, 5Amps
  • Charging current: 0.1Amp to 6Amp, User programmable in steps of 0.1Amps
  • Discharge current: 0.1A to 1A, User programmable
  • Current drain for balancing Li-Po batteries: 300mA per cell
  • Weight: 600gms
    Dimensions: 13.5cm x 14.5cm x 4.5cm
  • Optional Battery temperature monitoring
  • Includes charging cables for 5 different types of battery sockets.

Important

  • Charger doesn’t contain XT60 male connector. If your battery has XT60 male connector then contact NEX Robotics for XT60 to “T” type converter.
  • During discharge, bottom right side of the battery charger gets very hot. We strongly recommend keeping battery charger in standing position during discharging and if possible blow air using small fan to the back side of the charger. To extend the life of the battery charger we recommend restricting discharge current below 0.5Amps in all conditions. If possible avoid discharging of the batteries using this charger.
  • Read user manual completely before using B6AC Universal Battery Charger
  • If Li-Po batteries are deep discharged i.e. if voltage of the individual cell falls below 3.3V then battery charger will try to revive the individual cell. If it can not revive it then it will refuse to charge the deep discharged battery.
  • In order to prevent battery from deep discharging, use Battery Protection circuits from NEX Robotics
  • Damaged battery may catch fire while charging. Always charge battery in open space on non-flammable surface such as concrete. We strongly recommend putting battery inside Li-Po Guard Fire Proof Bag from NEX Robotics while charging the battery.
  • We strongly recommend charging Lithium Polymer Battery in balance mode only with maximum charging current between 0.5A to 2A. This insures that charger has sufficient capacity to keep control on balancing process.
  • To avoid risk of short circuit always insert charging cable’s banana connectors inside the charger first and then connect. Do not insert charging cable in reverse polarity. It will immediately damage battery and charger.

B6AC Universal Battery Charger

B6AC-Universal-Battery-Char

B6AC-Universal-Battery-wide

B6AC-Universal-Battery-long

B6AC Universal Battery Charger Accessory cables

B6AC-Universal-Battery-cab

Battery Protection circuits for Lithium Polymer Battery

Lithium-Polymer-Battery-Pro

Li-Po Guard Fire Proof Bag for Lithium Polymer Battery charging and storage

A26

Package Contains

One B6AC Universal Battery Charger
One mains power cable
One DC power cable
Five charging cables for different types of battery sockets

Download Manual

Visit forum for Online Discussion on this product



ROHS Compliant : YES


Customer Reviews:

There are yet no reviews for this product.
Please log in to write a review.



Customers who bought this product also bought this/these product(s)

T Type Battery Connector
T Type Battery Connector
Rs.61.67