Nex Robotics

Your Shopping Cart




Your Cart is currently empty.

   

You are here: Home Products Motor Drivers Hercules 6V-36V, 16Amp Motor Driver
PrintE-mail
100 Rs CouponUltrasonic Range Finder XL-EZ0 (MB1200)

Hercules 6V-36V, 16Amp Motor Driver
View Full-Size Image


Hercules 6V-36V, 16Amp Motor Driver

Product ID: NR-MDR-003
Weight: 120 gms
Price: Rs.2,179.36

Ask a question about this product

  
In Stock: 3

 

Introduction

Hercules 6V-36V, 16Amp Motor Driver can take up to 30A peak current load and can be operated up to 3 KHz PWM. Motor driver can be interfaced with 3.3V and 5V logic levels. Motor driver has built-in protection from under / over voltage, over temperature and short. The Motor driver has terminal block as power connector and 7 pin 2510 type relimate connector for the logic connection. It is suitable for high performance robots, Robocon, Robo-cup, US First, Battle robots etc.

Note:

Hercules 6V-36V, 16Amp Motor Driver can take up to 20Amp current if fan is installed on top of heat sink.

Specifications

  • Operating voltage: 6V to 36V
  • Continuous output current: 16Amp
  • Peak output current: 30Amps
  • Maximum PWM Frequency: 3 KHz
  • Over voltage and under voltage shutdown
  • Thermal shutdown
  • Protection against loss of GND and Vcc.
  • Motor fault diagnostics outputs for over temperature or short circuit
  • Power Connector: 4 Pin Terminal Block
  • Logic Connector: 7 pin female relimate connector (2510 type)
  • Size: 72.0mm x 38.0mm

Package contains

15cm,7 pin female 2510 type relimate connector
Four 10mm mounting studs
Eight M3 mounting screw

Download Product Manual

Important

  • Use multithread copper wire with at least 1.5mm2 area of cross section for proper current handling capacity.
  • It is highly recommended to use of 15A or 20A fuse in between motor driver’s supply line.
  • Motor driver is not reverse polarity protected. Applying reverse polarity will instantly damage the motor driver.
  • Make sure that motor supply ground and logic ground is common.
  • If you change motor’s direction suddenly while motor is moving in one direction even at 4Amps, depending on the type of the motor, surge current may reach to very high value and motor driver may go in to protection mode. Do not reverse the motor’s direction suddenly unless its required. It’s a good practice to give stop command to the motor for 10 to 100 milliseconds between sudden direction changes.

Correct Motor Driver Selection

For generic motion control applications we recommend Hercules series motor driver that provides satisfactory performance at affordable price. However, for precision servo control applications, Super Hercules series motor driver is strongly recommended. Following is the difference between these two series of the motor drivers.

In case of the Hercules series Motor Drivers, the PWM OFF signal switch off the lower MOSFETs. Which means during PWM off period the motor is free wheeling. DC brakeing is achieved by connecting IN-1 and IN-2 to the logic 1 or logic 0 simultaneously.

Super Hercules series Motor Drivers actually shorts the motor winding during PWM off cycle for tight motion control. It also uses Synchronous Rectification to reduce power dissipation across MOSFETs when motor windings are shorted. In order to do all this, it uses high power MOSFETs and smart motion control methods. In this case, DC brakeing is achieved by simply setting PWM to logic low.

Interfacing motor driver with the microcontroller

Hercules-CS-Motor-Driver-Mi

To drive the motor controller you just need PWM, INA and INB pins. These pins can have 5V as well as 3.3V logic levels. Diagnostics 1 (DG-1) and Diagnostics-2 (DG-2) pins are internally pulled up at 5V at the motor driver side and are only required if you want to detect over temperature and short circuit faults. Most of the microcontrollers which operate at 3.3V have 5V tolerant input pins. If pins are not 5V tolerant then to interface them to 3.3V logic level you need to scale down 5V to 3.3V logic using open collector buffers or any other 5V to 3.3V logic converters.

Use Fuse Holder with Fuse Blow Indicator to protect motor driver from overload

soft-fuse-blow-indicator-fr

Recommended Motors
Super Hercules DC Motor with Planetary Gearbox and Side Shaft Super Heavy Duty DC Gear Motors
Super-Hercules-Planetary-Ge Side-Shaft-Super-Heavy-Duty

Recommended Battery Any High discharge 3cell 11.1V Lithium Polymer battery above 1800mAh.

 

Any High discharge 3cell 11.1V Lithium Polymer battery above 1800mAh. Any High discharge 3cell 11.1V Lithium Polymer battery above 1800mAh.

Connections

Hercules-Motor-Driver-Pin-C

Motor Connector Pins

Pin Functionality
Ground Ground pin to be connected to the supply
Vcc Motor supply 6V to 36V DC
OUT-1 (A) Output 1 for the motor
OUT-2 (B) Output 2 for the motor

Logic input Connections:

Pin No.

Pin

Functionality

1

ENA

Ground

2

IN-1

Logic input for the motor direction.

3

Diagnostic 1 (DG-1)

Output pin with logic 1 output in normal operation. Represents side of the internal H bridge corresponding to IN-1. Pin is pulled to logic low by the motor driver in case of over temperature or overload due to short circuit.

4

PWM

Used to apply Pulse Width Modulation to control motor velocity

5

Diagnostic 2 (DG-2)

Output pin with logic 1 output in normal operation. Represents side of the internal H bridge corresponding to IN-2. Pin is pulled to logic low by the motor driver in case of over temperature or overload due to short circuit.

6

IN-2

Logic input for the motor direction..

7

CS

No Connection

If you want to drive motor without using PWM then connect PWM pin to 5V logic level

Truth Table in Normal Operating Conditions

IN-1 IN-2 Diagnostic 1
(DG-1)
Diagnostic 2
(DG-2)
OUT-1
(A)
OUT-2
(B)
CS Mode of Operation
1 1 1 1 H H N.A. Break to VCC
1 0 1 1 H L N.A Clockwise(CW)
0 1 1 1 L H N.A
Counterclockwise
(CCW)
0 0 1 1 L L N.A. Break to GND
In all above cases logic 0 and logic 1 on PWM pin will turn off or turn on internal low side MOSFETs.

Visit forum for Online Discussion on this product

 

 



ROHS Compliant : NO


Customer Reviews:

There are yet no reviews for this product.
Please log in to write a review.



Customers who bought this product also bought this/these product(s)

Red Led (SMD)
Red Led (SMD)
Rs.3.03
FRC FEMALE 10 pin
FRC FEMALE 10 pin
Rs.4.85
10 PIN FRC Cable
10 PIN FRC Cable
Rs.3.97
Fuse Holder with Fuse Blow Indicator
Fuse Holder with Fuse Blow Indicator
Rs.72.69



Contact Us

Please use HELPDESK to contact us.

Tel: +91-022-27782445

09.30 AM to 06.00 PM IST, Monday - Saturday

Address :
Nex Robotics Pvt Ltd.
Unit No. 13,
Building No. 2 (A3), Sector 1,
Millennium Business Park,
Mahape, Navi Mumbai 400 710,
Maharashtra, INDIA

NEX Robotics location on map

RESEARCH

Find out more about latest research work being done at NEX Robotics. Here you will find links/papers demonstrating research done on our latest development platforms.

NEWS

Nex robotics has added support for Microsoft Robotics Developer Studio (MRDS) on FireBird V research platform. FireBird V is one of the most widely deployed research platforms designed by Department of CSE, IIT Bombay and Nex robotics.

Read more...


NEX Robotics has designed Intelligent autonomous transport vehicle for transporting personals autonomously inside the campus and for advance research in mobile robotics.

Read more..

Newsletter Subscribe

FOLLOW US


We Accept

Currency Selector


Testimonals