Nex Robotics

Your Shopping Cart




Your Cart is currently empty.

   

You are here: Home Products New Products Arduino Compatible W5100 Ethernet Shield
PrintE-mail
200 RPM Side Shaft 37mm Diameter High Performance DC Gear MotorHeat Shrink Tube 30mm

Arduino Compatible W5100 Ethernet Shield
View Full-Size Image


Arduino Compatible W5100 Ethernet Shield

Product ID: NR-Arduino-Shield-W5100 Ethernet
Weight: 25 gms
Price: Rs.1,816.13

Ask a question about this product

  
In Stock: 2

Introduction:

This Arduino Ethernet Shield which is based on the Wiznet W5100(datasheet) Ethernet Chip gives you an easy way to get your Arduino Online. This version support micro SD card (TF card) to read and write The expansion board with a stackable design can be directly plugged into the Arduino. This is a clone without MCU on it and POE functions, but arduino stackable, achieve most functions for ethernet use. It uses the Ethernet library to write sketches which connect to the internet via a standard RJ45 Ethernet jack using the shield.

Arduino communicates with both the W5100 and SD card using the SPI bus (through the ICSP header). This is on digital pins 11, 12, and 13 on the Duemilanove and pins 50, 51, and 52 on the Mega. On both boards, pin 10 is used to select the W5100 and pin 4 for the SD card. These pins can not be used for general i/o. On the Mega, the hardware SS pin, 53, is not used to select either the W5100 or the SD card, but it must be kept as an output or the SPI interface won't work.

Note that because the W5100 and SD card share the SPI bus, only one can be active at a time. If you are using both peripherals in your program, this should be taken care of by the corresponding libraries. If you're not using one of the peripherals in your program, however, you'll need to explicitly deselect it. To do this with the SD card, set pin 4 as an output and write a high to it. For the W5100, set digital pin 10 as a high output.

Note:

  • This is not an original Arduino brand product, it is a look-alike Arduino Ethernet shield board with the same components and functionality.

Features:

  • Support Arduino official Ethernet Library.
  • It adds a micro-SD card slot, which can be used to store files for serving over the network.
  • It is compatible with the Arduino Duemilanove (168 or 328), Uno as well as Mega (1280/2560) and can be accessed using the SD library.
  • The Wiznet W5100 provides a network (IP) stack capable of both TCP and UDP.
  • It supports up to four simultaneous socket connections.
  • Use the Ethernet library to write sketches which connect to the internet using the shield.
W5100 Features:
  • Support Hardwired TCP/IP Protocols TCP, UDP, ICMP, IPv4 ARP, IGMP, PPPoE, Ethernet
  • 10BaseT/100BaseTX Ethernet PHY embedded
  • Support Auto Negotiation (Full-duplex and half duplex)
  • Support Auto MDI/MDIX
  • Support ADSL connection (with support PPPoE Protocol with PAP/CHAP Authentication mode)
  • Supports 4 independent sockets simultaneously
  • Not support IP Fragmentation
  • 0.18 μm CMOS technology
  • 3.3V operation with 5V I/O signal tolerance
  • Small 80 Pin LQFP Package
  • Lead-Free Package
  • Support Serial Peripheral Interface (SPI MODE 0, 3)Multi-function LED outputs (TX, RX, Full/Half duplex, Collision, Link, Speed)

Downloads:

EAGLE files: arduino-ethernet-shield-05-reference-design.zip
Read the tutorials and arduino demo code here.
Getting started with Arduino ethernet shield

ROHS Compliant : NO


Customer Reviews:

There are yet no reviews for this product.
Please log in to write a review.



Customers who bought this product also bought this/these product(s)

Berg strip 1X40 Male 20MM (0.1 INCH PITCH)
Berg strip 1X40 Male 20MM (0.1 INCH  PITCH)
Rs.20.35
1 to 1 Black Connector
1 to 1 Black Connector
Rs.6.05
1 to 1 Red Connector
1 to 1 Red Connector
Rs.6.06
Female 1 to 1 Connector Pack of 10
Female 1 to 1 Connector Pack of 10
Rs.42.40



Contact Us

Please use HELPDESK to contact us.

Tel: +91-022-27782445

09.30 AM to 06.00 PM IST, Monday - Saturday

Address :
Nex Robotics Pvt Ltd.
Unit No. 13,
Building No. 2 (A3), Sector 1,
Millennium Business Park,
Mahape, Navi Mumbai 400 710,
Maharashtra, INDIA

NEX Robotics location on map

RESEARCH

Find out more about latest research work being done at NEX Robotics. Here you will find links/papers demonstrating research done on our latest development platforms.

NEWS

Nex robotics has added support for Microsoft Robotics Developer Studio (MRDS) on FireBird V research platform. FireBird V is one of the most widely deployed research platforms designed by Department of CSE, IIT Bombay and Nex robotics.

Read more...


NEX Robotics has designed Intelligent autonomous transport vehicle for transporting personals autonomously inside the campus and for advance research in mobile robotics.

Read more..

Newsletter Subscribe

FOLLOW US


We Accept

Currency Selector


Testimonals